How To Fix an Xbox Series X Controller That Keeps Blinking Series

How To Fix an Xbox Series X Controller That Keeps Blinking Series

You’re all set for a long gaming session. You finally have the time and are ready to kick back and play your favorite Xbox games until the sun comes up. Your heart sinks when you pick up your Xbox controller and see it’s blinking.

How To Fix an Xbox Series X Controller That Keeps Blinking Series

Don’t worry, there’s no reason to panic. This isn’t a catastrophic event but an easily resolved issue. This article will cover some of the more common reasons why your controller is blinking, along with a fix for each one.

A blinking Series X controller is caused by one of two different factors, so the problem can be easily diagnosed. The usual culprits are either weak or dead batteries, or it’s become unpaired from the console. Or it could also be a combination of the two. We’ll discuss these and other possible situations, so no matter which of these scenarios is causing your controller to blink, each one is easily remedied.

Check the Controller’s Batteries

Weak or fully discharged batteries could be the reason your controller is blinking. If the batteries are weak, that means that your controller’s signal is weak, too. You can either replace the batteries or plug in the controller and wait until it’s fully recharged.

How To Create A Pin For Pinterest On A PC Or Mobile Device Mark anthony

When replacing the batteries, you should only use alkaline AA batteries that have the LR6 designation on them. These are rechargeable; however, they don’t recharge while in the controller. You’ll need to recharge them by following the manufacturer’s recommendation.

To install new batteries in your controller, follow these steps:

  1. In one hand, hold the controller upside down.
  2. With your thumb on the opposite hand, press the battery cover and push in the direction of the arrow.
  3. Once the cover is removed, replace the batteries taking note of the “-“ and “+” symbols to ensure they are installed correctly.
  4. Replace the battery cover by sliding it back into place.

It’s important to ensure that the batteries have been installed properly. Also of note, check to make sure the battery contacts aren’t bent, misshapen, or corroded.

You can check your controller’s battery strength by pressing the Xbox button and looking in the upper right corner of your screen. There you’ll see a battery icon indicating the current battery strength.

Check the Controller’s Range

It’s possible that your controller is too far away from the game console. Try moving closer to see if it stops blinking. Another possibility is that other devices are interfering with the connection. Microwave ovens, wireless routers, and other devices could be blocking the syncing process. Inspect the gaming area for things that could be causing an interference.



Too Many Connected Devices

Have you recently had a gaming party with your buddies where they paired their controllers with your console? An Xbox console can accommodate up to eight different controllers. If you have more than eight controllers synced to your console, you’ll have to unpair one or more in order for yours to be connected.

Unpairing a controller is a straightforward process. To do so, follow these instructions:

  1. Hold down the “Sync” button on the front of the controller until the Xbox button begins to flash.
  2. Wait until you feel the controller vibrate two times.

Ensure That Your Controller Is Properly Paired

Another common cause for a blinking controller could be that it’s no longer paired with your console. If you’ve brought it to a fellow gamer’s place and paired it to his or her device, then you’ll need to re-sync your controller to your console. There are two methods of pairing your controller.

The first method is to connect your controller to your console with a micro-USB cable. A hard-wired connection like this will instantly pair your controller. This will provide a more secure connection, and you’ll have fewer issues with your controller.

You can also pair your controller using the wireless method. To do so, follow these steps:

  1. Turn on your controller by pressing down and holding the “Xbox” button until it flashes. If it stays lit, your controller is already paired.
  2. If the light doesn’t turn solid, locate and press the “Pair” button located on the front of the controller.
  3. On the Xbox Series X console, press the “Pair” button. It’s located on the front right side of the device, just above the USB port.
  4. You’ll have 20 seconds to press and hold the “Pair” button on the controller.
  5. The light will flash as it searches for the console. Once it’s paired, the Xbox light will stay lit.

Try Updating Your Xbox Firmware

Your Xbox controller automatically receives updates every six months or so. However, if your controller is blinking and you’ve tried all of the other suggestions we’ve offered, perhaps updating your firmware is the solution. Here’s how to do it:

  1. On your controller, press and hold down the “Guide” button.
  2. When prompted on your monitor, press the “A” button.
  3. Select “Update Controller.”
  4. Once the update has finished, choose “Next.”

Restart Your Xbox Console

If all else fails, power off your controller. Turn off your console and unplug the power cord. Wait a few minutes before plugging in the console’s power cord and turning it back on. Power on your controller. Sometimes a simple hard reset will do the trick.

Contact Xbox Customer Support

If you’re still having problems, you can try contacting Xbox Customer Support. If your console is still under warranty, they may be able to assist you with having it repaired or replaced.

A Blinking Xbox Controller Is Trying to Tell You Something

A blinking controller is trying to get your attention and alert you to an issue. It’s usually weak batteries or because the controller is no longer paired. Recharging or replacing its batteries usually does the trick. If not, pairing the controller to your console again may resolve the issue. Make sure you have less than eight controllers paired and ensure that there aren’t any other wireless devices nearby which could cause interference.

Has your Xbox controller started to blink? Did you solve the problem by using one of the recommendations in this article? Let us know in the comments section below.